Image
image
image
image


DPMS LR-308 Upper Receiver - Assembling:


Build a DPMS LR-308 Upper Receiver with Free Float Handguard from Parts

Below is the steps taken for assembling the DPMS LR-308 Upper Receiver in the "Build 2" project.


Tools Needed to Assemble a 308 AR Upper

Tools:

Click the links below for more info and purchasing sources.


Parts Required to Assemble a 308 AR Upper

Parts:

DPMS LR-308 Upper Receiver Parts

  • Stripped Upper Receiver
  • Barrel
  • Barrel Nut
  • Free Float Handguard
  • Front Sight Gas Block
  • Bolt Carrier Group
  • Gas Tube

Step 1 - Prepare the 308 AR Upper Receiver

The first thing I did was to inspect every part and do a test run making certain all the parts fit as expected.

DPMS LR-308 Assembled


Step 2 - Prepare the 308 AR Stripped Receiver

Mount the stripped upper to the "Claw" and insert the two retaining pins. The pins require a slight tapping from a hammer. They are tight by design. Now at this point most folks will do the smart thing and place the claw in a vise for the rest of the assembly. I don't have a vise in my apartment so I will use the one at work a little farther down the page :)

DPMS 308 Action Block DPMS "Claw"


Step 3 - Install 308 AR Barrel

Installing the barrel is pretty straight forward. Be certain to clean the barrel extension and the mating hole in the upper receiver. I applied a thin layer of grease to the barrel extension to make future disassembly easier.

DPMS LR-308

Slide the barrel in place.

DPMS LR-308

Be sure to orient the pin of the barrel extension with the groove in the threads of the upper receiver

DPMS LR-308


Step 4 - Install 308 AR Barrel Nut

Apply grease to the threads. This to aid in the proper torque and future removal of the barrel nut. Typically a "Moly Grease" is used. This build I will be using the Militec-1 which is NOT a moly grease. I use the Militec for everything gun related.

Carefully hand tighten the barrel nut being sure not to cross the threads.

Grease reciever threads DPMS LR-308


Step 5 - Torque 308 AR Barrel Nut and Align Gas Tube

Here's the part where a bench vise must be used. The DPMS claw needs to be placed very securely in the vise as it takes a fair amount of force to tighten the barrel nut the correct amount while maintaining proper alignment for the gas tube.

The general idea with tightening the barrel nut is not to tighten it all in one shot but rather tighten it in three or four attempts. With each attempt you will tighten, back off and tighten again getting the barrel nut to rotate a little farther and tighter with each attempt. You will notice that the barrel nut holes most likely do not line up with the hole in the upper receiver for the gas tube. This is a good thing. Your final step is to tighten the barrel nut one last time and align the nut so the gas tube can fit through the barrel nut and into the receiver.

Basically you need to rotate to the next hole carefully stopping when the barrel not hole aligns with the gas tube hole in the receiver. Most folks use the gas tube testing for alignment as they go. I use a drill blank the correct diameter. I find it less awkward to use then the gas tube. Because of the very short handle on my wrench I had to use a hammer to gently tap the barrel nut into position.

Note: There is torque specification. If your using a different barrel nut and a wrench that allow the attaching of a torque wrench use the above procedure and stay within the correct torque range. Also the length of your wrench significantly affects the amount of torque you are applying to the barrel nut. The longer the wrench the more torque you will be able to apply with less physical force. Don't over tighten the nut or you can damage the receiver and possibly yourself.

DPMS LR-308 Tighten Barrel Nut

DPMS LR-308 DPMS LR-308 DPMS LR-308

DPMS LR-308 DPMS LR-308 DPMS LR-308

Align the barrel nut so the gas tube passes through the nut and into the lower receiver. In the image below you can see the rod visibly going through the barrel nut and into the receiver.

DPMS LR-308


Step 6 - Install 308 AR Gas Tube

This part is easy, just make certain the bend in the gas tube is oriented correctly. Actual installation will take place when the gas block is installed.

DPMS GAS System DPMS Rifle Gas TubeDPMS LR-308DPMS LR-308 Barrel Nut and Gas Tube

DPMS LR-308 Gas Tube Installation


Step 7 - Install 308 AR Front Sight Gas Block

This is another very easy step. The most important item to be concerned with is the orientation of the holes in the gas tube. The gas tube contains three holes. One hole aligns with the hole in the barrel. That hole is how the gas is able to get into the tube to assist with cycling the rifle. The other two holes will be aligned to each other horizontally. These two holes are for the roll pin the captures the gas tube within the gas block.

AR Gas Tube Ports DPMS LR-308 Gas Tube Orientation DPMS Gas Port

Place the correctly oriented gas tube into the gas block. Use a roll pin punch and small hammer to drive the roll pin flush with the gas block.

DPMS LR-308 Gas Block DPMS LR-308 Gas Block DPMS LR-308 Gas Block

Carefully slide the assembled gas block over the barrel. Notice are barrel has two small conical recesses machined into it. Those recesses are for the gas block set screws. They serve to lock the gas block in place and prevent it from rotating. The gas block will stop at the correct location due to the point where the barrel is a larger diameter. At this point I turn the upper receiver upside down so the picatinny on the upper and the gas block are resting on a perfectly flat surface. This aligns them perfectly to the same plane. Then carefully tighten the two set screws being careful not to move the gas block.

DPMS LR-308 Assembled Front Sight Gas Block

DPMS LR-308 Gas Block DPMS LR-308 Gas Block DPMS LR-308 Gas Block DPMS LR-308 Gas Block

Assembled it should look like this.

DPMS LR-308 Gas Block Assembled

DPMS LR-308 Gas Block Assembled

DPMS LR-308 Gas Block Assembled


Step 8 - Install 308AR Free Float Handguard

This step takes a little bit of fussing to get the handguard properly oriented so the bottom picatinny rail is square 180 degrees of the receivers picatinny. Once again I used some flat surfaces to square things up. Some guys mount a 12" rail to the top of this handguard then use a special tool from Brownells to hold the picatinny's inline and square while the handguard's locking ring is tightened.

Fulton Armory Titan Free Float Handguard


Step 9 - Install 308 AR Picatinny Rail

Two screws- Done. This was actually installed earlier to aid with aligning the handguard.

DPMS LR-308 Fulton Armory Picatinny


Step 10 - Verify Safe Headspace

Headspace is beyond the scope of this page. Consult a gunsmith or someone else qualified to verify proper headspace


Step 11 - Install 308 AR Bolt Carrier Group

No Explanation needed.


image
image
image