American Defense Manufacturing AD Recon-S Scope Mount

American Defense Manufacturing AD Recon-S Scope Mount

American Defense Manufacturing AD Recon-S Scope Mount

AD Recon-S Scope Mount

For a few years, the American Defense Manufacturing AD-RECON series of scope mounts have been my “Best Value” recommendation for QD AR mounts. For me, the AD Recon lineup represents the line where cost and performance converge. The AD Recon is one of the best values in one-piece mounts.

The American Defense Manufacturing AD-RECON-S Scope Mount is made for putting high-power glass onto a flattop style AR-10, Bolt Action Rifle, and Lever Action Rifles. This mount is best suited for the AR-10 platform or Bolt Action Rifles that are in a chassis system with a full-length handguard covering the barrel. This mount will work with up to and including 56mm Objective Lenses.

The AD-RECON-S is a straight-up scope mount with no eye relief built-in. It is precision machined from 6061 T6 aluminum and finished in hard coat T3 Mil-Spec anodize. It features the Patented QD Auto Lock Lever system to accommodate both in-spec and out-of-spec rail systems. Available in 30mm and 34mm rings and either Black or Flat Dark Earth and either no MOA, 20MOA, or 30MOA built-in.

Available from  Brownells, Optics Planet, Primary Arms, EuroOptic,

AD Recon-S Scope Mount

From American Defense Manufacturing

Quick-release lever-lock system clamps solidly to flattop rail and will not work loose even under heavy recoil—the more force acting on the lever, the tighter it locks. Depress the release tab to swing the lever open, and the mount easily lifts off the rifle. Adjustable with a flat head screwdriver or even a coin for an ultra-secure, no-slip fit on almost any Picatinny or Weaver-style rail, including over-or under-sized commercial rails. The lever may be configured to lock to the front or the rear to suit the operator’s preference.

A large locking bar on the side of the mount engages the maximum amount of rail area, while the cross-bolt and two integral locking lugs ensure rock-solid engagement of rail slots to prevent movement under recoil. Five heavy-duty steel hex head screws (three on top, two on bottom) clamp the vertically split ring halves together. Cutouts in the ring sides and in the base reduce weight without sacrificing strength. Quick-Release Scope Mount one-piece base with the dual-lever system provides the same solid mounting and fast removal and reattachment.

308 AR Integrated Folding Lower Receiver 17 Design

308 AR Integrated Folding Lower Receiver 17 Design

17 DESIGN AND MANUFACTURING AR-308 INTEGRATED FOLDING LOWER RECEIVER

17 Design Integrated Folding Lower Receiver

Introducing the Brownells exclusive 17 Design & Manufacturing  IFLR-10 (Integrated Folding Lower Receiver). The 17 Design & Manufacturing  IFLR-10 Stripped Lower Receiver is the perfect base for your AR 308 build.  The IFLR-10 has a folding stock mechanism machined directly into the AR lower receiver.

 All wearable parts are manufactured from S7 tool steel, which leads to extreme wear resistance, and corrosion-resistant coatings ensure your IFLR stays mint for years to come.

Available from Brownells

Additional Features:

  • Upper tensioning screw- allows user to fine-tune the fit of the upper and lower through the use of a nylon tipped tensioning set screw in the grip tang of the receiver.
  • Flared magwell angle- Wider angles in the magwell allow a more flared feel without increasing the width/footprint of the lower receiver.
  • Features a threaded bolt catch pin.
  • Comes with Specialty H1 Buffer, nylon tipped set screw, and assembled IFLR in stripped lower configuration ready for your custom build.

17 Design 308 AR Integrated Folding Lower Receiver

From the Manufacturer:

The patented Integrated Folding Lower Receiver was an idea floated several years back by a friend of 17 Design & Mfg, who would become the CEO of Shield Arms. We recently brought this idea back to life in a joint project as a submission and down-selected submission for the US Army’s Sub Compact Weapon System solicitation. While integrating a folding mechanism into the standard operating system of the AR-pattern rifle is far from simple, our extensive knowledge of manufacturing and engineering allowed for a high production, repeatable, first-of-its-kind product that will shape the AR market for years to come.

 

Triggertech AR-10 Diamond Trigger

Triggertech AR-10 Diamond Trigger

Triggertech 308 AR Diamond Trigger

Triggertech AR-10 Diamond Trigger (308 AR)

TriggerTech’s AR .308 Diamond Trigger is an enhanced design that allows you to take advantage of revolutionary new technology and gives you the flexibility to choose exactly what kind of trigger shoe works best for your shooting style. This trigger is available in Curved, Straight, and Pro Curved models, all designed to enhance your shooting skills and give you a more accurate, precise rifle platform.

Available from Palmetto State Armory, Brownells, Optics Planet

Triggertech AR-10 Diamond Trigger (308 AR)

In addition to the incredibly short 0.015-inch reset point, the TriggerTech .308 Diamond Trigger is also user-adjustable, so you can dial in your trigger-pull weight in two-ounce increments from 2.5 to 5 pounds, giving you the exact feel you want. The trigger housing is constructed from hard-anodized 7075 aluminum, and all the internal components are crafted from 440C stainless steel. The trigger is designed for AR .308 rifles, but it will fit any receiver built with mil-spec 0.154-inch pinholes.

The most important benefit offered by the TriggerTech AR .308 Diamond Trigger is its construction. Thanks to the incredibly innovative Frictionless Release Technology incorporated into the design, there are no contact surfaces that need polishing or lubrication, and there’s no wear that will gradually change your trigger-pull weight and feel over time. No matter whether you pull your trigger 1,000 or 10,000 times, it’ll remain consistent from shot to shot.

Intended Use

Long-range, competition, precision shooting, harsh environments, law enforcement, military, target shooting.

Triggertech 308 AR Trigger Specs

Triggertech AR-10 Trigger Specs

Trigger Control Specifications

Lever Type: Straight, Curved, or Pro Curved
Zero Creep™: Yes
TKR™: Yes – Min Overtravel
CLKR™: Yes – Inc. Adjustable
Flat Wire™: Yes – Hard Primer Compatible
Take Up Distance: 0.035″
Overtravel: Sub 0.015″
Reset: Sub 0.030″
Pin Size: Mil-Spec 0.154″ (trigger pins not included)
Material: 7075 Aluminum & Stainless Internals
Weapon Platform: AR10 (and pump-action AR)
Warranty: Product Lifetime
 

Material Details

Housing: 7075 Aluminum (anodized)
Key Components: 440C Stainless Steel
PVD Black – PVD stands for Physical Vapour Deposition. It is a hard and durable coating that is applied to external stainless components to give them a clean black color.
 
 

Full Description

Our AR10 Triggers are built for top competitive shooters to offer the most accurate and dependable trigger on the market. Featuring Frictionless Release Technology™, this drop-in AR trigger has a short, two-stage action, designed to feel like a 1911 trigger, that provides a true zero-creep break, extremely short overtravel, a sub 0.015” tactical reset and offers outstanding reliability, even in the harshest environments. Utilizing CLKR Technology™, the pull weight is quickly and confidently adjusted in 2oz increments from a set screw with the trigger installed. Due to there being truly zero creep, most shooters report the pull weights feeling ~0.5lbs lighter than a friction-based trigger of the same measured pull weight.

Changing the pull weight does not affect hammer force so you get dependable primer strikes at every weight. Frictionless Release Technology™, along with hardened 440C stainless steel internal components ensures corrosion resistance and extended service life. As Frictionless Release Technology™ does not rely on coating, polishing, or lubricating the key engagement surfaces, trigger pulls will be more consistent from shot to shot and after thousands of shots than you ever thought possible.

All pull weights and measurements are approximate.

The installation guide is directed to experienced professional gunsmiths who understand the workings of their AR rifle and know how to fully detail strip the lower receiver. If you do not have these skills, we strongly suggest you retain the services of a competent professional gunsmith to install your trigger, and perform all important safety checks.

Download the Triggertech AR-10 Trigger Installation Instructions here.

ATC AR Gold 308 AR Adjustable Trigger

ATC AR Gold 308 AR Adjustable Trigger

American Trigger Corp AR Gold AR 308 Adjustable Trigger

American Trigger Corp AR Gold 308 AR Adjustable Trigger

The American Trigger Corp AR Gold 308 AR Adjustable Trigger is a Self-contained trigger assembly that installs in minutes and delivers a light, smooth, match-grade trigger pull free of grittiness, with an ultra-crisp letoff and short reset. Simply remove the factory trigger and safety selector, drop in the module, reinstall the selector and pins, and you’re ready to shoot. Completely new engagement geometry produces a light 3-lb. pull and crisp release without compromising reliability or safety. The two-stage design is adjustable for sear engagement, with a first-stage takeup of approximately 6 ounces, followed by actual sear movement taking up the rest of the weight—the reverse of the military two-stage AR trigger pull profile. Instead, the shooter can build force steadily, maintaining precise control and keeping his attention on the target.

Available from Palmetto State Armory, Brownells, Optics Planet

Pact ATC AR Gold 308 AR Adjustable Trigger

Drop-In Fire Control System Gives A Light, Safe, Match-Grade Pull

After release, reset travel is only .030″, less than half the .070″ typical of standard match triggers, to aid in fast, accurate follow-up shots. The sear captures the hammer at the back instead of near the pivot point to help produce the light pull and maintain safety. A second, independent, intercepting sear is positioned to block the hammer if it slips off the primary sear, as when the weapon is dropped or suffers a hard impact. If the intercepting sear captures the hammer, pulling the trigger will still fire the rifle with a heavier pull weight. In addition, the Gold system uses the rifle’s factory safety to positively capture the hammer, like an M1 Garand, and roll it back below the primary sear for an extra margin of safety. A lightweight aluminum housing contains the entire system and maintains the correct tolerances between the working parts. The receiver pins serve only to anchor the module in the receiver, with no effect on the trigger function.

  • 3.5 lbs. (Adjustable Weight)
  • Drop Safe
  • Drop-In Module (easy installation)
  • Uses .154 pins
  • Shortest Reset
  • Designed for AR-15 & AR-10 Platform (.223, 5.56, .308, 7.62, .300 BLK, 6.5 Grendal)
  • 30 Day Money Back Guarantee
  • Made in the USA
  • Used by Top Competitive shooters including Jerry Miculeck and Daniel Horner

The AR Gold has known fitment issues with:

  • Receivers with Colt sear block
  • Receivers with firing pin lock installed (i.e., SIG MCX)

From the Manufacturer Pact American Trigger:

The ATC AR Gold has been proven to be the ultimate AR Platform trigger for military, LE, competition, hunting, and more. It is the singular best improvement to your AR-15. The AR Gold is a unique approach to the dated trigger functionality of stock AR-15’s and other competitors. The AR Gold is a drop-in module trigger, which makes it a breeze to install. It comes stock with a 3.5 lb pull weight. More than just the lightweight pull, the trigger has the shortest reset and cleanest break of any other trigger on the market. If that isn’t enough, it is also Drop-Safe.  Adjustable weight engagement and over-travel. .154 pins.  30 Day Money Back Guarantee on direct sales. Made in the USA by American Trigger Corporation.

ATC AR Gold Specifications

SPECS: Trigger/Hammer – Wire EDM cut S7 tool steel. Housing – Aluminum, anodized, black. SR/AR Gold fits ArmaLite® AR-10®, DPMS LR-308, Knight’s Armament SR-25, and similar AR-style .308 rifles with .154″ trigger and hammer pin holes.

Aero Precision OD Green and Tan 308 Breach Charging Handles

Aero Precision OD Green and Tan 308 Breach Charging Handles

Aero Precision OD Green and Tan 308 Breach Charging Handles
Aero Precision OD Green and Tan 308 Breach Charging Handles

Aero Precision OD Green and Tan 308 Breach Charging Handles

Now available in Tan Anodized and Olive Drab Green Anodize, the Aero Precision BREACH charging handle is here to meet the demands of your next build in style!

The rugged Aero Precision Breach Charging Handle offers quick and easy manipulation of your 308 AR platform for both right and left-handed shooters. Available in two different sizes, the small lever is perfect as a low profile, ergonomically friendly charging handle, while the large lever provides more real estate for purchase and manipulation of the product.

Machined in the USA from 7075 aluminum, the BREACH features an anodized finish and is manufactured with the same amount of quality and attention to detail you have come to expect from Aero Precision. Read Addition Details

Available from Brownells, Optics Planet, Primary Arms, Aero Precision

Aero Precision 308 Breach Charging Handle

Aero Precision 308 Breach Charging Handle

Aero Precision AR308 Breach Charging Handle

308 AR Breach Charging Handle

The rugged Aero Precision Breach Charging Handle offers quick and easy manipulation of your 308 AR platform for both right and left-handed shooters. Available in two different sizes, the small lever is perfect as a low profile, ergonomically friendly charging handle, while the large lever provides more real estate for purchase and manipulation of the product.

Machined in the USA from 7075 aluminum, the BREACH features an anodized finish and is manufactured with the same amount of quality and attention to detail you have come to expect from Aero Precision.

Check availability at Brownells, Optics Planet, Aero Precision

Aero Precision Breach Ambidextrous Charging Handle

Description:

The Aero Precision BREACH is a rugged, ambidextrous, precision-manufactured charging handle for the M5/AR308 platform. The BREACH’s design utilizes a reinforced 7075 aluminum bar that is up to the most demanding tasks. Its ambidextrous levers feature a patent-pending, dual spring system, that directs the force-of-use into the robust charging handle body. This allows the shooter to use a one-handed charging technique without compromising the part — a pitfall for traditional charging handles.

  • The small lever configuration provides a low-profile, easily gripped interface that is comfortable when slung and can be actuated effortlessly from either side of your rifle.
  • The large lever configuration provides an extended operating surface, perfect for a user with bigger hands, or someone who wants a larger surface for manipulation of the charging handle.

Features:

  • Ambidextrous Controls: Ergonomically designed 7075 Aluminum levers allow the user to easily charge their firearm with either hand while remaining low profile and comfortable when slung.
  • Robust Construction: Reduced chamfer angles on the 7075 Aluminum reinforced bar design provide a strong foundation for the BREACH that is resistant to rotational flex or breakage.
  • Patent-pending Lever Mechanism: Transfers force-of-use away from the roll pins and into the top/head portion of the reinforced bar protecting the charging handle in the most demanding circumstances.
  • Gas Deflection Shelf: Aligns with the upper receiver to redirect gas flow away from the user’s face when shooting suppressed.
  • Functional Design: It is not all just good looks. Stylistic cuts on the charging handle also help to clear stuck on carbon and debris from the upper receiver, while the spacer design seals and protects the lever mechanism from debris.

Additional Information:

  1. The Aero Precision BREACH is a rugged ambidextrous charging handle, perfect for your next build!
  2. The BREACH features a patent-pending, ambidextrous two-lever system allowing easy operation for right and left-handed shooters, utilizing a dual spring system for redundancy.
  3. The back of the BREACH charging handle features a wall that works to index the charging handle on the upper receiver as well as help redirect any gas blowback away from the shooter’s face when shooting suppressed.
  4. The body of the BREACH charging handle itself is thicker than traditional charging handles and features a reduced chamfer up top. This increases the durability of the part and makes for a more rugged charging handle design.
  5. Each BREACH charging handle features a load-bearing surface on the charging handlebar that maintains contact with the levers when the handle is being pulled. This takes the stress off the roll pins, traditionally a failure point on mil-spec charging handles.
  6. Available in a small lever, and large lever variant. The small lever provides a streamlined profile perfect for use in conjunction with a sling, while the large lever provides slightly more operating surface while taking steps to avoid becoming intrusive when used with a sling.
  7. The Aero Precision breach is available for both AR15 and M5/AR308.

 

Picture of an Aero Precision Breach Charging Handle