308 AR Charging Handle Option and Upgrades. DPMS 308, DPMS GII and Armalite AR-10 Compatible
308 AR Charging Handle
BCM Gunfighter Charging Handle 308 AR
BCM Gunfighter Charging Handle | 308 AR Charging Handle
When the AR15 system was first introduced to and fielded by the US Military in the 1960s, the manual of arms for an infantryman was significantly different than what currently exists today. To charge the rifle the shooter released their hand from a firing grip, grabbed each side of the charging handle with the thumb and forefinger or the first two fingers, (while applying pressure to the latch) pulled the charging handle all the way to the rear, and then released it to charge the weapon.
Like everything else in the last 45 years, tactics and weaponry have undergone a continuous evolution. Red dot optics get the shooter on target quicker, shorter barrels allow the operator to more quickly negotiate tighter urban areas, and operator’s manipulations of the weapon system have become much more efficient and faster. The current manual of arms has the operator maintaining a firing grip almost continuously while manipulating the weapon with the non-dominant hand in an effort to more quickly get the weapon ready to fire. With that premise, most weapon manipulations are done only with the shooter’s support hand; to include operating the charging handle.
In order to perform an immediate action or charge the carbine, current CQB techniques have the operator racking the charging handle to the rear using their support side hand only. This is done in one swift and strong movement. With the operator’s firing grip maintained, the weapon again has a loaded chamber, and the shooter can immediately bring a hot weapon back into the fight.
The current use of extended tactical latches has made this movement much more efficient. The only drawback to this type of manipulation is all the force used to rack the charging handle rearward goes into the extended tactical latch and is then transferred into the roll pin. With this scenario, the entire operation becomes contingent on the sheer strength of this tiny 1/16” roll pin, and its ability to take continuing blows. Repeated and forceful support hand only racking of the charging handle eventually can lead to breaking the roll pin and loosing the latch completely. With the latch blown out, the charging handle will not stay secured to the receiver as the bolt is moving back and forth during each cycle of the weapon’s action. Not a good situation on a two way range.
The BCMGUNFIGHTER Charging Handle and extended latches feature internal redesigns to direct the force off of the roll pin and into the body of the charging handle during support hand only manipulations. This new design has a built in backstop engineered into the extended latch and into the charging handle. As the latch is opened up, its’ travel is limited by these flat surface backstops. With this travel limiting feature, the stress is taken off the roll pin, and is now redirected into the entire body of the charging handle.
The BCMGUNFIGHTER™ Charging Handle offers two significant advantages.
- Since the tiny roll pin is no longer the weak point – it is a much stronger system and tactical latch will stay intact even under repeated support side only manipulation
- With the force kept inside the body of the handle, when the handle is pulled directly to the rear, it moves directly to the rear and does not angle off to the outboard side. A much smoother operation.
Mecharmor Defense Systems TacOps-1 Charging Handle
308 AR Charging Handle – Ambidextrous tactical charging handle can be operated with minimal body movement in confined spaces, under concealment, or even in the prone position. Lets you to maintain constant visual contact with the target during magazine changes, jam clearances, and other high-stress CQB situations. Extended, ergonomically shaped grasping surface provides an extra-secure grasp and extra leverage for normal charging operation, yet won’t interfere with the forward assist or oversized optics that extend behind the rear of the receiver. Dual-mode latch mechanism has a second release button in the center rear of the handle for easy handle operation with the support hand, further increasing your operational versatility. The heavy-duty latch roll pin resists breakage under hard use, and the 7-pound stainless steel latch spring ensures the latch locks down tight—and stays locked—until you release it.
SPECS: 7075 T6 aluminum, hardcoat anodized, Teflon coated, black. .223/5.56 fits AR-15/M16/M4. .308 fits AR-Style .308 rifles
“The MechArmor TacOps-1 ambidextrous charging handle is the only product of its type to be awarded the National Tactical Officers Associations coveted GOLD Seal of Testing & Recommendation award after rigorous field testing.”
Mecharmor Defense Systems TachOps-1 | 308 AR Charging Handle